SPA-2XCHOC12/DS0

SPA-2XCHOC12/DS0 Specifications

(channelized OC-12)

Visual status indicators (LEDs):

• SPA status LED

• Per-port LEDs

• Carrier and alarm

• Active and loopback

RFC 1662, Point-to-Point Protocol (PPP) in High-Level Data Link Control (HDLC)-like framing

Cisco HDLC

Multilink PPP (RFC 1990) (as applicable for 2-port channelized OC-12c/STM-4 (DS-1/E1)

FRF.12, link fragmentation and interleaving (LFI)

PPP, HDLC, and Frame Relay User Network Interface (UNI) encapsulations

• Full- and half-duplex connectivity at DS-3 rate (44.736 MHz)

• Scrambling and subrate support of major data-service-unit (DSU) vendors

• C-bit or M23 framing (software selectable)

• MDL

• Support for 16- and 32-bit cyclic redundancy check (CRC) (16-bit default)

• 24-hour history maintained for error statistics and failure counts

• DS-3 alarm and event detection (once-per-second polling)

• Alarm indication signal (AIS)

• Out of frame (OOF)

• Far-end receive failure (FERF)

DS-1

• Superframe (SF) and Extended Superframe (ESF) support

• ANSI T1.403 FDL support

• Internal or line-derived (loop) clocking, independently selectable on each T1 tributary

• Error and alarm detection: CRC errors, framing errors, loss of frame (red), AIS (blue), remote alarm indication (yellow)

• Alarm reporting: 24-hour history maintained, 15-minute intervals on all errors

• BERT at T1 level

• Loopback capabilities: local, network line and network payload, remote network line, and remote network payload at the T1 level

• Local (internal) or loop timed (recovered from network)

• Pointer activity monitoring

• Redundant clock source should be provisioned on different SPAs as only a single timing source can be provided by SPA

Local (diagnostic) and line (network) loopback

Payload mapping

• POS with 1 + X^43 self-synchronous scrambler

SONET/SDH compliance:

• Telcordia (Bellcore) GR-253-CORE (as applicable)

• ANSI T1.105, T1.231

• ITU-T G.707, G.957, G.825 (as applicable)

Supported SONET/SDH alarm and signal events:

• Signal failure bit error rate (SF-ber)

• Signal degrade bit error rate (SD-ber)

• Signal label payload construction (C2)

• Path trace byte (J1)

• Section

• Loss of signal (LoS)

• Loss of frame (LoF)

• Error counts for B1

• Threshold crossing alarms (TCA) for B1

• Line

• Line alarm indication signal (LAIS)

• Line remote defect indication (LRDI)

• Line remote error indication (LREI)

• Error counts for B2

• TCA for B2

• Path

• Path alarm indication signal (PAIS)

• Path remote defect indication (PRDI)

• Path remote error indication (PREI)

• Error counts for B3

• TCA for B3

• Loss of pointer (LoP)

• Positive stuffing event (PSE)

• Negative stuffing event (NSE)

• Path unequipped indication signal (PUNEQ)

• Path payload mismatch indication signal (PPLM)

SONET/SDH-MIB (RFC 2558)

CISCO-SONET-MIB

DS-3/E3-MIB (RFC 3896)

DS-1/E1-MIB (RFC 2496)

Simple Network Management Protocol (SNMP)

Field-replaceable SFP optical modules

1+1 SONET Automatic Protection Switching (APS) and SDH Linear Multiplexer Section Protection (MSP) protocols (please check platform support)

Single SPA software reset

Height: 1.56 in. (3.96 cm) (double height)

Width: 6.75 in. (17.15 cm)

Depth: 7.28 in. (18.49 cm)

Storage temperature: -38 to 150°F (-40 to 70°C)

Operating humidity: 5 to 85% relative humidity

Storage humidity: 5 to 95% relative humidity

• UL 60950

• CSA 22.2-No.60950

• EN60950

• IEC 60950 CB Scheme

• ACA TS001

• AS/NZS 3260

• EN60825IEC60825 laser safety (SR, IR-Class 1) (VSR-Class 1M)1

• 21CFR1040 -FDA Code of Federal Regulations (USA) laser safety (SR, IR-Class 1) (VSR-Class 1M)1

EMC

• FCC Part 15 (CFR 47)

• ICES 003

• EN55022

• CISPR 22

• AS/NZS CISPR22

• VCCI

• EN55024

• EN50082-1

• EN61000-6-1

• EN61000-3-2

• EN61000-3-3

Network Equipment Building Standards (NEBS)

This product is designed to meet the following requirements (official qualification may be in progress):

• SR-3580 – NEBS: Criteria levels (Level 3 compliant)

• GR-63-CORE – NEBS: Physical protection

• GR-1089-CORE – NEBS: EMC and safety