PWR-C45-1300ACV
| Model: | PWR-C45-1300ACV Cisco Catalyst 4500 PoE Enabled Power Supply |
| Detail: | Cisco Catalyst 4500 Power Supply PWR-C45-1300ACV Catalyst 4500 1300W AC Power Supply (Data and PoE) |
Warranty: supplied with the Green Code 1-year standard hardware repair warranty. Any manufacturer warranty terms shown in the specifications below are the manufacturer’s own.
Cisco PWR-C45-1300ACV is a Catalyst 4500 1300W AC Power Supply (Data and PoE). It belongs to the Catalyst 4500 PoE Enabled Power Supply range. Go by the part number. Items like this are routinely identical to look at and specific in what they actually fit.
Redundancy only works if they match. A pair of supplies has to be the same model and the same airflow direction, or the chassis will either refuse the second unit or run it in a way that defeats the point. Check the chassis generation first, since supplies with identical connectors are frequently not interchangeable, then the input type and the output rating against the full load.
How we supply it. Supplied new where available, otherwise as tested stock with warranty, subject to availability. If you are unsure whether this is the right part, give us the model it is going into and we will confirm it.
PWR-C45-1300ACV Specification | |
AC-input type | Autoranging input with power factor corrector Note Power factor correction is a standard feature on all Catalyst 4500 E-series AC-input power supplies. PFC reduces the reactive component in the source AC current allowing higher power factors (typically 99 percent or better) and lower harmonic current components. |
AC-input voltage | Low-line (120 VAC nominal)—85 VAC (min) to 132 VAC (max) High-line (230 VAC nominal)—170 VAC (min) to 264 VAC (max) |
AC-input current | 16 A @ 100 VAC 7 A @ 240 VAC |
AC-input frequency | 50/60 Hz (nominal) (±3 Hz for full range) |
Branch circuit requirement | Each chassis power supply should have its own dedicated, fused-branch circuit: For North America—15 A or 20 A For International—Circuits sized to local and national codes All Catalyst 4500 E-series AC-input power supplies require single-phase source AC. All AC power supply inputs are fully isolated. – Source AC can be out of phase between multiple power supplies in the same chassis, which means that PS1 can be operating from phase A and PS2 can be operating from phase B. – For high-line operation, the power supply operates with the hot conductor wired to a source AC phase and the neutral conductor wired either to ground or to another source AC phase as long as the net input voltage is in the range of 170 to 264 VAC. – Source AC can be out of phase between AC inputs on power supplies that are equipped with multiple AC inputs, which means that power cord 1 can be plugged into phase A and power cord 2 can be plugged into phase B. |
Power supply output capacity | 1300 W maximum 1050 W+ 40 W redundant mode (data) 1667 W maximum in combined mode (data) 800 W maximum each in redundant mode (PoE) 1333 W maximum in combined mode (PoE) |
Power supply output | 84.7 A @ 12 V @ (data) 12.5 A @ 3.3 V (data) 16.7 A @ –50 V (PoE) |
Output holdup time | 20 ms minimum |
Maximum kVA rating | 1.76 kVA |
Max heat dissipation | 1568 BTUs/hr |
Minimum software requirement | Cisco IOS Release 12.1(12c)EW |
Power over Ethernet (PoE) | Supported, up to 800 W (211 Cisco phones in combined mode) |
Power supply LEDs and their meanings | |
INPUT OK | Green—Source AC voltage is OK. (Input voltage is 85 VAC or greater.) Off—Source AC voltage falls below 70 VAC, is not present, or the power supply is turned off. |
FAN OK | Green—Power supply fan is operating properly. Off—Power supply fan failure is detected. |
OUTPUT FAIL | Red—Problem with one or more of the DC-output voltages of the power supply is detected. Off—DC-output voltage with acceptable margins. Note For proper operation of the OUTPUT FAIL LED, systems with single power supplies must be configured with a minimum of one fan tray assembly and one supervisor engine. Systems with dual power supplies must have a minimum configuration of one fan tray assembly, one supervisor engine, and one additional module. Failure to meet these minimum configuration requirements can cause a false power supply output fail signal. |
Q & A
Trusted IT Hardware,
Delivered Right.
Green Code Technologies is a UK-based IT hardware supplier trusted by businesses across 50+ countries — for genuine equipment, worldwide delivery, and expert support.
Enterprise IT Solutions Partner
Genuine, warranty-backed hardware from leading brands including Cisco, Huawei, HPE, Dell, Fortinet and more.
UK & Worldwide Delivery
We deliver across the UK and export worldwide. Lead times vary by product and are confirmed at quotation.
100% Authentic Hardware
Every product is verified for authenticity with verifiable serial numbers. We supply only genuine and certified equipment.
Expert Technical Support
Our in-house engineers provide free pre-sales and post-sales support to help you choose the right product for your infrastructure.
Competitive Pricing
We work to bring you the best enterprise IT hardware value without compromising on quality or warranty.
Sustainable IT Solutions
Sustainability is at our core. We offer eco-friendly certified-refurbished options alongside new hardware to reduce your organisation's carbon footprint.



























Reviews
There are no reviews yet