P03684-S01

HPE P03684-S01 is a ProLiant ML110 Gen10 3104 1.7GHz 6-core 1P 8GB-R S100i 4LFF NHP 350W PS DVD Entry AMS Server. It belongs to the ProLiant ML110 Gen9/10 Servers range.

What to check before you buy. Three things decide whether a server will suit the job. The generation, because the processors, memory and controllers that fit one generation generally do not fit the next even where the chassis looks identical. The drive configuration, because a chassis built for small form factor disks cannot take large form factor ones without a different cage and backplane. And how it is specified to be populated, since a second processor usually needs its own heatsink and may enable memory slots that are otherwise unusable. It is also worth asking what is physically included: rails, bezel, drive carriers and the remote management licence are all commonly sold separately from the chassis.

How we supply it. Supplied new where available, otherwise as tested stock with warranty, subject to availability. Send us the host model along with the part number and we will check compatibility before you commit. We reply by the next working day.

This is HPE part P03684-S01: an HPE ProLiant ML110 Gen10, supplied as a complete, pre-configured server rather than a chassis to specify yourself — Intel Xeon Scalable 3104 (6 cores, 1.7 GHz); 8 GB RDIMM; 4 x 3.5-inch (LFF), non-hot-plug.

The HPE ProLiant ML110 is a single-socket tower, built to sit in an office or a small comms room rather than a rack, and quiet enough to do it.

What is in this configuration

The S100i storage controller

The S100i is software RAID, not a hardware controller. It handles SATA drives only and has no cache and no battery-backed write protection, and because the RAID is done by the chipset and driver it is supported on a narrower set of operating systems than a hardware card. For a boot pair or a lightly used volume it is perfectly adequate. If you plan to run SAS drives, or you want write caching, you need a hardware controller instead and we can quote one.

This server ships with registered memory

The -R suffix means RDIMM, registered memory, which is what mainstream ProLiant servers use. It allows far higher total capacity than unbuffered memory and it is what you want if the server will grow. Registered and unbuffered memory cannot be mixed, so any upgrade needs to be RDIMM too.

Power supplies, and whether this build is redundant

This build lists a single 350 W power supply and no redundant cage. On the smaller ProLiant chassis these supplies are often not hot-plug either, so a failure means downtime and a visit. If this server matters, tell us and we will check whether the chassis supports a redundant pair.

Drive bays

These are 3.5-inch (LFF) bays. Large-form-factor bays take the big nearline drives, which is the cheaper route to bulk capacity and the usual choice for backup targets and archives. Note that these bays are non-hot-plug. Changing a disk means powering the server down and opening it, which matters more than it sounds: a failed drive becomes scheduled downtime rather than a five-minute job. If this server needs to stay up through a disk replacement, tell us and we will quote a hot-plug configuration instead.

Worth checking before you order

• These drive bays are non-hot-plug. Replacing a disk means powering the server down. Ask us for a hot-plug configuration if that is a problem.
• The S100i is software RAID and supports SATA only. If your plan involves SAS drives, this configuration will not take them and you need a hardware controller.
• Single power supply, no redundancy. Ask us before you assume this chassis takes a second one.
• Pre-configured does not mean fixed. We can change the memory, drives, controller or network adapters before despatch, which is usually cheaper than buying the base build and upgrading it afterwards. Tell us what it needs to do.
• Drives are not normally included in these configurations. Confirm what you need and we will quote them with the server so the caddies and firmware match.
• Tell us what this server is replacing and what it has to run, and we will confirm this build is the right one rather than just the one you found.